Was trying to figure out if the 904 and the 727 valve body's are the same? Most parts have them listed together??

So the '49 needs a brake upgrade, some wiring issues tightened up/finished, and the seat belts need to get installed. Also, since I ran out of gas tonight, I need to get a new fuel gauge sending unit.

Oh, I guess I need to be a little more active here too. Sorry about that, guys.

I am eyeballing some sheet metal parts too!

Hello hello !!


More questions... again...:-)

My Coronet has WP27E67265374

Is this early in the production or late??

regarding there is two different Jack instructions...

Should I get a F or a G sticker ?????

7902]


as usual ...;-) all help is very appreciated


and


To all of you

Have a great day


BR
//Anders

Attached Files

Thumbnail(s)
   

Just wondering if anyone had a simple explanation of what is going on with the 4 different Band Lever ratio's for a 727 tranny. which ratio is better? I am doing a recalibration kit in mine and, more than likely, going from a 2.? ratio to a 5.0 ratio lever. Why is the 4.2 lever so much higher than the 5.0 lever? I got the Fairbanks Transaction Kit, and I am going full competition on this transmission!

Has anyone run a relay system for their headlights?

Hi again!!


Does someone in this great forum know if it's possible to buy Bumper Guards somewhere?



New (are there any aftermarket?), NOS or used - All info appreciated

(Have seen the rubber inserts on Ebay, but not the chrome parts)

Like the looks with these mounted




7901]

Since the picture was taken ... new tires in the back (same as the front tires)...:-)


Best Regards
//Anders

Attached Files

Thumbnail(s)
   

Hi, would be great to archieve any history of my R/T. It`s a 1968, GG1, green interior, A833, Dana 60 car. Looking for prvious owner, build sheet and so on. THX<br><br>
1968 Coronet R/T VIN: WS23L8G184438

7900]

Attached Files

Thumbnail(s)
   

Some nice reproduction parts that folks might need for their Coronets.

Richard

New Mopar 1966 Coronet Hood Lip Molding Trim

Ebay auction link: http://www.ebay.com/itm/401068429815?_tr...EBIDX%3AIT



New 1967-74 A-Body and 1966-70 B-Body Bulk Head Connector Seal Kit

Ebay auction link: http://www.ebay.com/itm/400999723635?_tr...EBIDX%3AIT



[B]New 1967 B-Body Lower Steering Column Cover[/B]

Ebay auction link: http://www.ebay.com/itm/161966921205?_tr...EBIDX%3AIT


[B]New Mopar Federal Power Steering Pump Brackets For 1967-72 Big Block And Hemi Applications[/B]

Ebay auction link: http://www.ebay.com/itm/181870276743?_tr...EBIDX%3AIT




[B]New Mopar 1964-69 TRW Power Steering Pump Brackets For Big Block[/B]

Ebay auction link: http://www.ebay.com/itm/400987627885?_tr...EBIDX%3AIT




[B]New Mopar 1967-68 Big Block A/C Alternator Bracket Kit[/B]

Ebay auction link: http://www.ebay.com/itm/181852367478?_tr...EBIDX%3AIT

Where would a stock hose hook to? There is a port on our intake with a plug in it. Is this where a nipple would be or would it be on the carburetor?

It looks like ours has residue of turquoise paint. An ad for a '67 shows the 440 and fuel pump looks natural unpainted. I know ads are just that but wondering? Experiences?
ALSO water pump heater hose nipples? Painted or not?