Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Power steering box issues
#1
Has anyone rebuilt a power steering box? It looks kinda complicated in the service manual. Mine has a lot of play and I tried adjusting the screw on top and it didn't help. That's when I noticed the input shaft is walking in and out an excessive amount as it turns back and forth. The input shaft seal is leaking a crazy amount when the front end is jacked way up. Just to be clear the play is in the steering box, the ball joints, torsion bars, lower control arm bushings, inner and outer tie rod ends were replaced in the past few years and the idler arm and pitman arm are brand new.
Reply Purge Spammer

#2
I have done a few and not too hard but I have all the factory tools which helps allot.
Now might be time to consider a upgrade to a firm feel.
The Idaho Andy
I love the smell of race fuel in the morning
Reply Purge Spammer

#3
I’ll look into it. I know they’re cheaper than borgsen.
Reply Purge Spammer

#4
I rebuild one on a 69 imperial I had, that was probably 20 years ago. I don’t remember it being hard to do
Nobody wants a Charlie in the box
Reply Purge Spammer

#5
From what you guys say I believe I cound do it if it was just seals and bearings but I don't see where the input end play can be adjusted. Rock Auto has Cardone rebuilding service listed for $107. I contacted Cardone and they said 3 to 5 business days with an 80% probability of success with the information I gave them. I think if I go that route I'll still have time to get a Firm Feel box in before Carlisle if Cardone can't fix it, even though it's over my budget.
Reply Purge Spammer

#6
Firm Feel rebuilt the p/s box on my Coronet. I opted for the Stage III - love it. They also rebuilt the man box on my Dart. They're more than $107, but all they do is Mopars.
Reply Purge Spammer

#7
Seriously considered the Firm Feel but it just wasn't in the budget. It's in Texas right now being rebuilt by Cardone. If they can't tighten it up then I'll just be the captain of the SS Coronet until I can save up for the Firm Feel. At least I won't have the oil film all over the back of my car.
Reply Purge Spammer



Possibly Related Threads…
Thread Author Replies Views Last Post
  Steering Column Length Piper 19 9,901 11-20-24, 08:38 PM
Last Post: 67r/t4speeder
  bolt pattern power booster mopar440 2 979 05-11-22, 07:59 PM
Last Post: 67440Dodge
  Correct '66 B-Body power steering hose routing theman440 8 1,646 03-30-22, 07:00 PM
Last Post: 67440Dodge
  Power Steering Pump ID 67440Dodge 1 3,456 05-19-16, 10:57 PM
Last Post: 67r/t4speeder
  Power brakes-vacuum hose to carb or intake? 67RTBlue 5 4,561 04-30-16, 01:33 PM
Last Post: 67r/t4speeder
  Brake questions-power vs non, plumbing 67RTBlue 15 8,672 04-25-16, 03:05 PM
Last Post: 67r/t4speeder
  proper steering wheel? Dave Wallace 34 15,528 04-13-16, 01:49 AM
Last Post: Dave Wallace
  Is the firewall different on a factory power brake car? 67RTBlue 2 3,379 04-07-16, 07:57 PM
Last Post: theman440
  67 Coronet power window question Lipers1 8 5,324 10-11-15, 01:47 AM
Last Post: thebankerstoy
  Power steering lines and pump Jpr777 7 4,436 09-25-15, 01:59 PM
Last Post: thebankerstoy

Forum Jump:


Users browsing this thread:
3 Guest(s)

Powered By MyBB, © 2002-2024 Melroy van den Berg.