12-28-14, 01:12 AM
II am looking for stainless steel window trim for a 1967 coronet. Does anyone have any ideas?
|
Windshield trim
|
12-28-14, 02:15 AM
It's available from most used parts dealers. It's not that rare as it shared many models and a couple years.
Where are you from? And welcome to the site, please tell us about your 500.
President, New England chapter of Coronetaholics anonomous.
12-28-14, 03:01 PM
Welcome!
Objects quickly DISAPPEAR in the rearview mirror and PLEASE stay seated until the ride comes to a complete stop!!
12-28-14, 11:32 PM
Thanks for all welcomes .. I am from Sacramento area of CA. I have been working on a 1967 Dodge Cornett 500. Rebuilt original 318 motor with Newer Magnum heads and other goodies. According to build sheet should be about 400 hp. All original interior including gauges( one small split in driver seat to be reupholstered ) 727 trans. I am putting on a slotted rotor disc brake front end. 18" rockets on the corners.
Also working on 1964 Comet Caliente & 1968 AMX390. .... But that's another story. I have looked everywhere on line and can't seem to find leads on the front and rear windshield trim.
12-29-14, 02:14 AM
Try wildcat wrecking in Washington or Oregon, sorry not sure which one.
You're not too far away from Andy, at least by east coast standards. Maybe he can give you a lead.
President, New England chapter of Coronetaholics anonomous.
12-29-14, 02:20 PM
The Idaho Andy
I love the smell of race fuel in the morning 
12-29-14, 02:39 PM
'67Coronet500 Wrote:Thanks for all welcomes .. I am from Sacramento area of CA. I have been working on a 1967 Dodge Cornett 500. Welcome! My daughter's 67 Coronet 500 is originally from Sacramento!
67 Coronet 500 - 9.610 @ 139.20 mph
Owned Since 1981 Daughter's Car 67 Coronet 500 Street Car with AC 13.300 @ 101.75 mph 69 GTX clone - build in progress........ 
12-29-14, 03:34 PM
(This post was last modified: 12-29-14, 03:37 PM by thebankerstoy.)
Welcome to the DCR community!
Below is a link to an Ebay auction for a full set of the front windshield moulding trim. Seller mentions a few small dings, but this trim is stainless, so it can be worked back to excellent condition if you're careful. This front windshield moulding trim is the same on all 1966 and 1967 Dodge Coronet and Dodge Charger 2 door hardtop models and all 1966 and 1967 Plymouth Belvedere, Satellite and GTX 2 door hardtop models. Richard P.S. Looks as if Andy typed faster that I did, as his Ebay auction link is the same as mine.  Ebay auction link: http://www.ebay.com/itm/66-67-Coronet-RT...7f&vxp=mtr
For some unknown reason, nobody seems to take me seriously............
12-29-14, 04:16 PM
thebankerstoy Wrote:Welcome to the DCR community! You just took time to explain thing like I did not, mines just SPLAT!! here you go LOL
The Idaho Andy
I love the smell of race fuel in the morning
12-30-14, 12:33 AM
I decided to go ahead and do an additional thread in the DCR Coronet Restoration forum regarding a front windshield outside moulding trim parts interchange guide to help folks understand what parts were used on specific 1966 and 1967 Dodge and Plymouth B-Body models. Hopefully this parts interchange guide will help folks who are looking for these parts.
Here's the link to that thread: http://www.dodgecoronet.com/forum/showth...#post23602 Richard
For some unknown reason, nobody seems to take me seriously............
|
| Users browsing this thread: |
| 2 Guest(s) |