DodgeCoronet.com
What did you do to your Coronet this Week ....??? - Printable Version

+- DodgeCoronet.com (https://dodgecoronet.com/forum)
+-- Forum: Where The Fun Happens (https://dodgecoronet.com/forum/forumdisplay.php?fid=3)
+--- Forum: General Discussion (https://dodgecoronet.com/forum/forumdisplay.php?fid=12)
+--- Thread: What did you do to your Coronet this Week ....??? (/showthread.php?tid=525)



What did you do to your Coronet this Week ....??? - theman440 - 10-23-13

Rebuilt both passenger side door hinges - thanks for the tip Rich!


What did you do to your Coronet this Week ....??? - ws27 - 10-23-13

Thanks, my stubbornness, and other known problems led me to buy an exhaust bender this spring. Haven't used it yet, but can't wait.


What did you do to your Coronet this Week ....??? - FRATZOG - 10-24-13

ws27 Wrote:Thanks, my stubbornness, and other known problems led me to buy an exhaust bender this spring. Haven't used it yet, but can't wait.
That would be a pretty nice piece to own...


What did you do to your Coronet this Week ....??? - Racer Brown - 10-24-13

ws27 Wrote:Thanks, my stubbornness, and other known problems led me to buy an exhaust bender this spring. Haven't used it yet, but can't wait.
Rich, you can set up shop now, the orders from this site will be pouring in!!!!!!!!!!!


What did you do to your Coronet this Week ....??? - 67r/t4speeder - 10-24-13

Nothing

[Image: CRYING.gif]


What did you do to your Coronet this Week ....??? - ws27 - 10-24-13

I need to set up an outlet and just play with it a little.

Then the first Guinea pig... Jim's wagon. HEHEHEHE


What did you do to your Coronet this Week ....??? - ws27 - 10-24-13

67r/t4speeder Wrote:Nothing

[Image: CRYING.gif]

No sympathy here buddy. LOL


What did you do to your Coronet this Week ....??? - FRATZOG - 10-25-13

It was only 2 deg Celsius (not quite 36 deg F) this morning, but I drove her to work anyway. Smile


What did you do to your Coronet this Week ....??? - Zaq - 10-28-13

Over the weekend I finished plumbing my dual pot master, bled the brakes, found a pinhole leak in one of the lines, replaced that line, bled them again, installed a new drive shaft, installed a B&M shifter, filled rear end with gear lube, added transmission fluid to find it it drips from one of the cooler lines (no surprise, anytime I add a new fluid to the car it leaks out somewhere until I can fix it).

Only thing stopping me from taking it for a spin around the block is waiting for a thermostat gasket because the store had to order one. It will be the first time it has moved under its own power since 1981.


What did you do to your Coronet this Week ....??? - ws27 - 10-28-13

Zaq Wrote:Over the weekend I finished plumbing my dual pot master, bled the brakes, found a pinhole leak in one of the lines, replaced that line, bled them again, installed a new drive shaft, installed a B&M shifter, filled rear end with gear lube, added transmission fluid to find it it drips from one of the cooler lines (no surprise, anytime I add a new fluid to the car it leaks out somewhere until I can fix it).

Only thing stopping me from taking it for a spin around the block is waiting for a thermostat gasket because the store had to order one. It will be the first time it has moved under its own power since 1981.

Nice, can't wait to till you get it running.