+- DodgeCoronet.com (https://dodgecoronet.com/forum)
+-- Forum: Where The Fun Happens (https://dodgecoronet.com/forum/forumdisplay.php?fid=3)
+--- Forum: General Discussion (https://dodgecoronet.com/forum/forumdisplay.php?fid=12)
+--- Thread: What did you do to your Coronet this Week ....??? (/showthread.php?tid=525)
Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
What did you do to your Coronet this Week ....??? - 67r/t4speeder - 10-19-13
Hey I'm not that blue guy am I ?
What did you do to your Coronet this Week ....??? - thebankerstoy - 10-20-13
ws27 Wrote:OK, how about this?
![[Image: hanging.gif]](http://kennl.dk/smileys/images/hanging.gif)
Helga was packing a bag of "goodies" to come visit you after that first attempt Rich, but you've done very well on your second try, so Helga will postpone her visit to you ........for now!
Richard
What did you do to your Coronet this Week ....??? - krowbar - 10-21-13
Did my $60 oil change with Valvoline VR1 10w30. Put some Lucas trans stop leak in the 727. Put a New tach on the column. Put 2 New bolts in the trans crossmember to replace the ones that weren't there( MIA ). Then took it down the road and laid some rubber.
What did you do to your Coronet this Week ....??? - 67r/t4speeder - 10-21-13
krowbar Wrote:Did my $60 oil change with Valvoline VR1 10w30. Put some Lucas trans stop leak in the 727. Put a New tach on the column. Put 2 New bolts in the trans crossmember to replace the ones that weren't there( MIA ). Then took it down the road and laid some rubber.VR1 is the good stuff
What did you do to your Coronet this Week ....??? - FRATZOG - 10-22-13
Just finished replacing the original dual exhaust with 2 1/2" 14 gauge pipes and Thrush Welded mufflers. Sounds awesome and It certainly performs better too! Me likey.
What did you do to your Coronet this Week ....??? - 67r/t4speeder - 10-22-13
FRATZOG Wrote:Just finished replacing the original dual exhaust with 2 1/2" 14 gauge pipes and Thrush Welded mufflers. Sounds awesome and It certainly performs better too! Me likey.
What did you do to your Coronet this Week ....??? - Jay Nordstrom - 10-22-13
FINALLY!!! The car is at Sullivan Motorsports for the long awaited 727 to torque flight swap. Cannot wait for the 2014 race season.
What did you do to your Coronet this Week ....??? - ws27 - 10-22-13
FRATZOG Wrote:Just finished replacing the original dual exhaust with 2 1/2" 14 gauge pipes and Thrush Welded mufflers. Sounds awesome and It certainly performs better too! Me likey.
Just out of curiosity, if you don't mind answering, what did you pay for a complete dual exhaust. They are getting 800 bucks in my area. I don't see how, but they get it.
What did you do to your Coronet this Week ....??? - FRATZOG - 10-23-13
ws27 Wrote:Just out of curiosity, if you don't mind answering, what did you pay for a complete dual exhaust. They are getting 800 bucks in my area. I don't see how, but they get it.Lucky for me, I still have lots of contacts in the biz. I bought 4 10' lengths of straight 2 1/2 " 14 gauge pipe, two Thrush Welded mufflers (the welded ones have deeper tone), and because I am still running factory manifolds; I needed two reducers with 3/8" thick flanges... total for parts: $290 Canadian. The custom bending and welding was just straight time and costed me $280 Can. So I got away with about $570 taxes in
... I was happy
The pipe was not stainless as it's a PIA to bend without cracking. It really needs to be mandrel bent when still warm.
Really, $800 is not that bad if it includes everything including good mufflers.
What did you do to your Coronet this Week ....??? - hotrod AL - 10-23-13
Just installed my remanufactured Holley 1920 on my slant6. Old one was pouring gas all over the manifolds when it would accelerate. Saved $100 by going the Rockauto route.