+- DodgeCoronet.com (https://dodgecoronet.com/forum)
+-- Forum: Where The Fun Happens (https://dodgecoronet.com/forum/forumdisplay.php?fid=3)
+--- Forum: General Discussion (https://dodgecoronet.com/forum/forumdisplay.php?fid=12)
+--- Thread: What did you do to your Coronet this Week ....??? (/showthread.php?tid=525)
Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
What did you do to your Coronet this Week ....??? - 4264door - 07-10-13
I have the very same problem so yes...I believe it does shrink cars!
What did you do to your Coronet this Week ....??? - BigBlock61 - 07-12-13
I started repairing the rust holes in the tail panel for my Coronet.
What did you do to your Coronet this Week ....??? - 67r/t4speeder - 07-12-13
Drove mine to work
What did you do to your Coronet this Week ....??? - thebankerstoy - 07-12-13
67440Dodge Wrote:When you run a roller lifter, you have to run a cam that is ground for them. Otherwise they'll do nasty things to each other..
Thanks Mike and that makes sense. I guess that I'm just confused on what applications the "hydraulic roller" lifters are used on.
Richard
What did you do to your Coronet this Week ....??? - 67440Dodge - 07-13-13
It's just another way of activating valves. Much more efficient than a flat tappet. They've been available since the 60's, and OEM's have been using them since the 90's on V8's and V6's
What did you do to your Coronet this Week ....??? - lanceh13 - 07-13-13
67r/t4speeder Wrote:Drove mine to work
Isn't that every day? #jealous
What did you do to your Coronet this Week ....??? - lanceh13 - 07-13-13
My coronet sat lonely in the garage while I have been cheating on it in Carlisle. I peek in on her from time to time with my spy cam though...one day I will actually get my motor dropped in....but certainly not this week.
What did you do to your Coronet this Week ....??? - 67r/t4speeder - 07-13-13
lanceh13 Wrote:My coronet sat lonely in the garage while I have been cheating on it in Carlisle. I peek in on her from time to time with my spy cam though...one day I will actually get my motor dropped in....but certainly not this week.
Plop that beast in there Lance, nutn to it .
What did you do to your Coronet this Week ....??? - lanceh13 - 07-13-13
67r/t4speeder Wrote:Plop that beast in there Lance, nutn to it .
Says the guy with every mans dream garage / career...we can't all drive our coronets on a daily basis Andy. lol
What did you do to your Coronet this Week ....??? - Copper67440 - 07-14-13
This week I installed a new Yearone M & H dash harness. That was actually last night. Drove it to a couple of cruises today. Probably a little over a hundred miles round trip. The amp guage was acting a little hinky right when I started it. It seemed to go a little too high on the charge side and actually fluctuated like a tach for a few. I checked the battery voltage with the car off at 12.93v. It was too late last night to let it run longer than a minute.
Like I said I drove it today and the guage went to the middle and moved just a little both ways all day. I'm a happy camper!!