+- DodgeCoronet.com (https://dodgecoronet.com/forum)
+-- Forum: Where The Fun Happens (https://dodgecoronet.com/forum/forumdisplay.php?fid=3)
+--- Forum: General Discussion (https://dodgecoronet.com/forum/forumdisplay.php?fid=12)
+--- Thread: What did you do to your Coronet this Week ....??? (/showthread.php?tid=525)
Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
What did you do to your Coronet this Week ....??? - JimKueneman - 10-10-16
Restored and installed the original brake lines, clips and proportional valves. Also restored and installed the parking brake. Would have installed the fuel line but I welded a hole in it fixing the floorboard before it removed it... duh...
9257]9258]9259]9260]9261]9262]9263]9264]9265]9266]9267]9268]
What did you do to your Coronet this Week ....??? - 67r/t4speeder - 10-10-16
Jim I have been there done that with restoring those original lines and you have done an excellent job, I appreciate all that hard work you have done. Keep it up.
What did you do to your Coronet this Week ....??? - JimKueneman - 10-10-16
Do you have suggestions on fixing the fuel line? I ended up with a weld droplet on the line that I tried to "scrape" off and it ripped a hole in the line. I could get a new one from Classic but I would rather have the original.
What did you do to your Coronet this Week ....??? - JimKueneman - 10-10-16
Just for fun here is where I started this spring and where I am today...
9269]9270]
What did you do to your Coronet this Week ....??? - 67r/t4speeder - 10-10-16
How about a compression union
What did you do to your Coronet this Week ....??? - JimKueneman - 10-11-16
67r/t4speeder Wrote:How about a compression union
Ouch, a good stainless steel one is not cheap.... ~$15 then I need to rent the tools make the flares..... The replacement is looking better
What did you do to your Coronet this Week ....??? - 67r/t4speeder - 10-11-16
![[Image: -font-b-Brass-b-font-Fit-font-b-15mm-b-f...dapter.jpg]](https://ae01.alicdn.com/kf/HTB18PSRNXXXXXbUXVXXq6xXFXXXy/-font-b-Brass-b-font-Fit-font-b-15mm-b-font-OD-Tube-Coupler-Adapter.jpg)
Get a brass one at the auto parts store like this, they seal better than stainless. No need to flare anything. Would not use if fuel injected engine due to pressure.
What did you do to your Coronet this Week ....??? - JimKueneman - 10-11-16
67r/t4speeder Wrote:Get a brass one at the auto parts store like this, they seal better than stainless. No need to flare anything. Would not use if fuel injected engine due to pressure.
I thought about that but was not sure about the corrosion of dissimilar metals....
What did you do to your Coronet this Week ....??? - RT K_line - 10-11-16
X2 on the brass union will work with no problem, nice job so far by the way.
What did you do to your Coronet this Week ....??? - JimKueneman - 10-12-16
Ok, I'll give it a shot.