+- DodgeCoronet.com (https://dodgecoronet.com/forum)
+-- Forum: Where The Fun Happens (https://dodgecoronet.com/forum/forumdisplay.php?fid=3)
+--- Forum: General Discussion (https://dodgecoronet.com/forum/forumdisplay.php?fid=12)
+--- Thread: What did you do to your Coronet this Week ....??? (/showthread.php?tid=525)
Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
What did you do to your Coronet this Week ....??? - metaldad - 05-10-16
installed new motor mounts, from Schumacher.
What did you do to your Coronet this Week ....??? - TekHousE - 05-11-16
I did 2 things this week..
Put in a Hurst Pro-Matic 2 shifter in the factory console..
I made a 'howto' topic about this elsewhere in this forum.http://www.dodgecoronet.com/forum/showthread.php?3709-Hurst-pro-matic-2-conversion-in-my-67-Coronet-IN-FACTORY-CONSOLE!
And added a Hotchkis sway bar to the front end. Replacing my stock factory one. Since putting the rear sway bar on last year I was feeling like I was getting some 'push' from the rear through corners. This happens when the stiffness of the rear bar matches or exceeds the front. Which I knew would happen when we installed the rear one. I was not sure how much this was going to affect things but at the start of the season this year I decided to change the front for a much heavier Hotchkis one.
8368]8369]
What did you do to your Coronet this Week ....??? - Mark's 69 - 05-11-16
theman440 Wrote:Mark,I haven't really got to run it enough for an evaluation. The only issue I had with installation was the intake. I had paper gaskets along with the valley pan on the iron heads and I couldn't get the Weiand manifold bolt holes to line up in that configuration. No problems with just the valley pan and some sealant. The long reach of the spark plugs made it difficult to install without loosening the headers but they cleared fine once they were seated. I was able to use the stock rocker assemblies so that saved a lot of cash. Bruce did some nice port work and provided the flow numbers, I could post them if you'd like. Zoran has been running his longer so he could probably give you a better idea.
How do you like those heads?
What did you do to your Coronet this Week ....??? - TekHousE - 05-11-16
I can tell you I love mine. Hands down the best set I've ever had on a mopar. Bruce ported mine to what you might call Stage III, they flow very well for the street. I don't run headers so the spark plug access is fine. I have the Mopar HP manifolds. I have plenty of miles (KM's ) on mine now too. So I am sure if there were going to be issues I would have seen them by now.
If you have any questions just ask away!
Here are my flow numbers - underneath the 'Out of box' numbers.
8370
I looked at your photos on the previous page Mark, nice! As you know I painted my heads, I wanted to go stealth-mode. But did you know that I have the ONLY pair WITHOUT the CPPA stamps?
I got the very first set destined for the street. I heard there are another pair on a drag car, but Bruce told me that is still not up and running yet.8371
What did you do to your Coronet this Week ....??? - theman440 - 05-12-16
Mark's 69 Wrote:I haven't really got to run it enough for an evaluation. The only issue I had with installation was the intake. I had paper gaskets along with the valley pan on the iron heads and I couldn't get the Weiand manifold bolt holes to line up in that configuration. No problems with just the valley pan and some sealant. The long reach of the spark plugs made it difficult to install without loosening the headers but they cleared fine once they were seated. I was able to use the stock rocker assemblies so that saved a lot of cash. Bruce did some nice port work and provided the flow numbers, I could post them if you'd like. Zoran has been running his longer so he could probably give you a better idea.
DId your guy happen to flow them Before porting_ I wonder if they flow better than a stock head_
What did you do to your Coronet this Week ....??? - TekHousE - 05-12-16
Check my figures..Both BEFORE and after are there. LOL
What did you do to your Coronet this Week ....??? - theman440 - 05-12-16
Do you know how those numbers compare to a stock 906 or 452?
What did you do to your Coronet this Week ....??? - TekHousE - 05-13-16
theman440 Wrote:Do you know how those numbers compare to a stock 906 or 452?
I can get that data for you if you want.
I have to add here at this point a few comments about flow.
I guess that some of you already understand what I am going to write so bear with me.
FLOW is not the only indicator you want to be looking at. There are plenty of heads that flow better than the figures I posted, but you must also look at velocity of the flow itself. High flow heads can also be turbulent. Many times those PEAK figures are exactly that..They quote the highest figure attained as the FLOW rate of the particular head being tested. But I would question how CONSISTENT that flow was and what velocity was it. It is no good to have high flow rate but a very turbulent flow.
What did you do to your Coronet this Week ....??? - TekHousE - 05-15-16
OK here are the flow numbers for all of those heads vs the CPPA ones.
8385]
What did you do to your Coronet this Week ....??? - theman440 - 05-15-16
Thanks Man!